How to inspect and replace engine/transmission mounts in 2.3L and 2005 and later 2.0L engine on Ford Focus?

The engine/transmission mounts should not commonly need inspection or replacement until they are broken or worn but in the event of a broken mount or mount that is worn significantly the mount must be replaced at once with a view of preventing a damage or wear out of the drive line assembly. It is often possible to lift an individual mount and replace it repeatedly and independently Even if several of the mounts are displaced confirming that they should be reunited they will require to be reassembled and their fasteners tightened at the positions which are indicated during their removal. During reassembly the total weight of the engine/transmission unit should not be put on the mounts until all the units come into correct alignment over the marks made at the time of removal of the engine/transmission unit, and the mounting bolts must be tightened up to the prescribed torque. In this case, the engine/transmission unit should be lifted slightly off the mounts to reduce the load upon it, and the car in turn should be firmly placed on axle stands. A jack with a block of wood should be placed directly under the oil pan to lift the engine/transmission just enough in order to offload some weight from the mountings. As for the modes of the vehicle operation, the mounts should be inspected for the cracks, the hardened rubber, the separation from the metal parts of the vehicle or the relative movement of the mount brackets relative to the engine/transmission or the body. If there is movement, the motor should be lowered at that point and the fasteners securing it examined and probably tightened. For replacement, the engine should be supported beneath the oil pan with some form of jackstand. The coolant expansion bottle is anchored to the right-hand mount and the mount operational position is marked on the automobile. The locking nuts of the engine casing should be loosened and the retaining bolts to the inner fender panel of the vehicle should be removed to pull-out the mounting with the engine/transmission supported. In assembly all the nuts and bolts must be tightened to the required torque first is the locking nuts to the engine casing then the mounting bracket to inner fender retaining bolts. In the case of the left-hand mount, few modifications are needed; the air intake hose has to be disconnected and the air cleaner assembly has to be taken off. After the transmission is supported, center retaining nut should be turned counter clockwise to be loosened for the removal of the mount and the outer retaining nut for the dismount of the mount in the mounting bracket. The mounting bracket can be removed by the removal of retaining bolts which are tightened on the bracket. At the time of installation, new self-locking nuts must be used, and all the bolts screwed to the required torque. For the rear mount it has to be removed by loosening the center bolt which is on the subframe and on the transmission and when putting it back it has to be tightened to the required torque.

Genuine Ford Focus Motor And Transmission Mount

Motor and Trans Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

40 Motor And Transmission Mounts found

View related parts
Ford Focus Transmission Extension Housing
Part Number: AV6Z-6068-A
$85.08 MSRP: $87.33
You Save: $2.25 (3%)
ADD TO CART
Product Specifications
- Other Name: Housing - Transmission Extension
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | 3 Cyl 1.0L EcoBoost 120PS/125PS/140PS, 4 Cyl 2.0L DI TIVCT Petrol, 4 Cyl 2.0L EcoBoost (240PS) , Electric Motor | 5-Speed Manual Transmission - MTX75, 6-Speed Automatic Transmission DPS6, 6-Speed Manual Transaxle - MMT6, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Focus Housing
Part Number: CV6Z-6068-A
$37.34 MSRP: $38.33
You Save: $0.99 (3%)
ADD TO CART
Product Specifications
- Other Name: Lower Trans Mount, Torque Arm, Transmission Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | 3 Cyl 1.0L EcoBoost 120PS/125PS/140PS, 4 Cyl 2.0L DI TIVCT Petrol, 4 Cyl 2.0L EcoBoost (240PS) , Electric Motor | 5-Speed Manual Transmission - MTX75, 6-Speed Automatic Transmission DPS6, 6-Speed Manual Transaxle - MMT6, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Focus Engine Front Support Bracket
Part Number: BV6Z-6038-A
$146.63 MSRP: $150.50
You Save: $3.87 (3%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Front Mount, Motor Mount, Mount
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2014 Ford Focus | 4 Cyl 2.0L EcoBoost (240PS) | 1-Speed Transmission, 5-Speed Manual Transmission - MTX75, 6-Speed Automatic Transmission DPS6, 6-Speed Manual Transaxle - MMT6, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Focus Insulator Mounting Bracket
Part Number: 5S4Z-6038-CB
$69.20 MSRP: $101.17
You Save: $31.97 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Insulator Mounting; Motor Mount, Mount
- Manufacturer Note: For Warm Climates Only
- Replaces: 5S4Z-6038-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2011 Ford Focus | 4 Cyl 2.0L Duratec HE | 4-Speed Automatic Transaxle - 4F27E, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Focus Insulator Mounting Bracket
Part Number: 5S4Z-6038-CA
$89.61 MSRP: $101.17
You Save: $11.56 (12%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Insulator Mounting
- Manufacturer Note: For Cold Weather States
- Replaced by: 5S4Z-6038-CB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Ford Focus | 4 Cyl 2.0L Duratec HE | 4-Speed Automatic Transaxle - 4F27E, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Focus Engine Mounting Bracket
Part Number: YS4Z-6028-AA
$24.61 MSRP: $44.83
You Save: $20.22 (46%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mounting; Support Bracket
- Manufacturer Note: Att. to 6038 RH insulator and side member, MTX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2004 Ford Focus | 4 Cyl 2.0L, 4 Cyl 2.0L Zetec EFI, 4 Cyl 2.0L Zetec VVT | 4AT 4F27E, 5MT, 5-Speed Manual Transmission - B5/IB5, 5-Speed Manual Transmission - MTX75, 6MT, 6-Speed Manual Transmission, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Focus Engine Front Support Bracket
Part Number: AV6Z-6038-A
$77.86 MSRP: $113.83
You Save: $35.97 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Motor Mount, Mount
- Position: Front
- Replaces: CV6Z-6038-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | 4 Cyl 2.0L DI TIVCT Petrol | 1-Speed Transmission, 5-Speed Manual Transmission - MTX75, 6-Speed Automatic Transmission DPS6, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Focus Engine Front Support Bracket
Part Number: CV6Z-6038-C
$75.35 MSRP: $110.17
You Save: $34.82 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Motor Mount, Mount
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | 4 Cyl 2.0L DI TIVCT Petrol | 1-Speed Transmission, 5-Speed Manual Transmission - MTX75, 6-Speed Automatic Transmission DPS6, 6-Speed Manual Transaxle - MMT6, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Focus Automatic Trans Mount
Part Number: 8S4Z-6068-A
$45.01 MSRP: $64.67
You Save: $19.66 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Lower Trans Mount, Transmission Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2011 Ford Focus | 4 Cyl 2.0L Duratec HE | 4-Speed Automatic Transaxle - 4F27E, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Focus Engine Mount Bushing-Right
Part Number: 5S4Z-6038-BB
$75.35 MSRP: $110.17
You Save: $34.82 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Insulator Mounting; Front Insulator, Motor Mount, Mount
- Manufacturer Note: For Warm Climates Only
- Position: Passenger Side
- Replaces: 5S4Z-6038-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2011 Ford Focus | 4 Cyl 2.0L Duratec HE | 5-Speed Manual Transmission - MTX75, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Focus Rear Insulator
Part Number: 5S4Z-6068-AA
$35.26 MSRP: $50.67
You Save: $15.41 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing
- Manufacturer Note: Replacement Parts Are Slightly Different And Tech May Need To Improvise
- Position: Rear
- Replaces: 1M5Z-6068-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2007 Ford Focus | 4 Cyl 2.0L CVH EFI, 4 Cyl 2.0L Duratec HE, 4 Cyl 2.0L Zetec EFI, 4 Cyl 2.0L Zetec VVT, 4 Cyl 2.3L | 4-Speed Automatic Transaxle - 4F27E, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Focus Engine Front Support Bracket
Part Number: DV6Z-6038-B
$99.98 MSRP: $146.17
You Save: $46.19 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Motor Mount, Mount
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2014-2018 Ford Focus | 4 Cyl 2.0L EcoBoost (240PS) | 1-Speed Transmission, 5-Speed Manual Transmission - MTX75, 6-Speed Automatic Transmission 6F15, 6-Speed Automatic Transmission DPS6, 6-Speed Manual Transaxle - MMT6, 6-Speed Manual Transmission - B6, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Focus Transmission Extension Housing
Part Number: DV6Z-6068-A
$83.90 MSRP: $122.67
You Save: $38.77 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing - Transmission Extension; Transmission Mount, Upper Trans Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2014-2018 Ford Focus | 4 Cyl 2.0L EcoBoost (240PS) , 4 Cyl 2.3L Ecoboost | 6-Speed Manual Transaxle - MMT6, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Front-Wheel Drive (Right Hand Drive), Left Hand Drive, RHD 4WD (FTD)
View related parts
Ford Focus Housing
Part Number: BV6Z-6068-A
$50.86 MSRP: $66.17
You Save: $15.31 (24%)
ADD TO CART
Product Specifications
- Other Name: Torque Arm
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2018 Ford Focus | 3 Cyl 1.0L EcoBoost 120PS/125PS/140PS | 6-Speed Automatic Transmission 6F15, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Focus Engine Mounting Bracket
Part Number: 8S4Z-6A036-A
$13.73 MSRP: $18.75
You Save: $5.02 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mounting; Mount Bracket
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2011 Ford Focus | 4 Cyl 2.0L Duratec HE | 4-Speed Automatic Transaxle - 4F27E, 5-Speed Manual Transmission - MTX75, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Focus Bracket
Part Number: 3M5Z-6031-A
$15.39 MSRP: $22.50
You Save: $7.11 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Motor Mount Support Bracket
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | 3 Cyl 1.0L EcoBoost 120PS/125PS/140PS, 4 Cyl 2.0L DI TIVCT Petrol, 4 Cyl 2.0L EcoBoost (240PS) , 4 Cyl 2.3L Ecoboost, Electric Motor | 1-Speed Transmission, 5-Speed Manual Transmission - B5/IB5, 5-Speed Manual Transmission - MTX75, 6-Speed Automatic Transmission 6DCT450 - MPS6, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F15, 6-Speed Automatic Transmission DPS6, 6-Speed Manual Transaxle - MMT6, 6-Speed Manual Transmission - B6, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Front-Wheel Drive (Right Hand Drive), Left Hand Drive, RHD 4WD (FTD)
View related parts
Ford Focus Engine Mounting Bracket
Part Number: CV6Z-6031-A
$20.29 MSRP: $29.67
You Save: $9.38 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mounting; Front Mount Bracket
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | 3 Cyl 1.0L EcoBoost 120PS/125PS/140PS, 4 Cyl 2.0L DI TIVCT Petrol, 4 Cyl 2.0L EcoBoost (240PS) , Electric Motor | 1-Speed Transmission, 5-Speed Manual Transmission - MTX75, 6-Speed Automatic Transmission 6F15, 6-Speed Automatic Transmission DPS6, 6-Speed Manual Transaxle - MMT6, 6-Speed Manual Transmission - B6, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Focus Engine Front Support Bracket
Part Number: CV6Z-6028-A
$19.04 MSRP: $27.83
You Save: $8.79 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Rear Mount Bracket
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | 3 Cyl 1.0L EcoBoost 120PS/125PS/140PS, 4 Cyl 2.0L DI TIVCT Petrol, 4 Cyl 2.0L EcoBoost (240PS) , Electric Motor | 1-Speed Transmission, 5-Speed Manual Transmission - MTX75, 6-Speed Automatic Transmission 6F15, 6-Speed Automatic Transmission DPS6, 6-Speed Manual Transaxle - MMT6, 6-Speed Manual Transmission - B6, Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Focus Engine Front Support Bracket
Part Number: G1FZ-6038-A
$110.69 MSRP: $161.83
You Save: $51.14 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Motor Mount, Mount
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2018 Ford Focus | 4 Cyl 2.3L Ecoboost | 1-Speed Transmission, 5-Speed Manual Transmission - B5/IB5, 5-Speed Manual Transmission - MTX75, 6-Speed Automatic Transmission 6DCT450 - MPS6, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F15, 6-Speed Automatic Transmission DPS6, 6-Speed Manual Transaxle - MMT6, 6-Speed Manual Transmission - B6, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Front-Wheel Drive (Right Hand Drive), Left Hand Drive, RHD 4WD (FTD)
View related parts
Ford Focus Housing
Part Number: CM5Z-6068-A
$90.06 MSRP: $131.67
You Save: $41.61 (32%)
Product Specifications
- Other Name: Lower Trans Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | 3 Cyl 1.0L EcoBoost 120PS/125PS/140PS, 4 Cyl 2.0L DI TIVCT Petrol, 4 Cyl 2.0L EcoBoost (240PS) , 4 Cyl 2.3L Ecoboost, Electric Motor | 1-Speed Transmission, 6-Speed Manual Transaxle - MMT6, Four-Wheel Drive (Full Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Front-Wheel Drive (Right Hand Drive), Left Hand Drive, RHD 4WD (FTD)

| Page 1 of 2 |Next >

1-20 of 40 Results

Ford Focus Motor And Transmission Mount

Motor And Transmission Mount in Ford Focus plays a very important part as it is responsible for fixing the transmission and protecting it from vibrations of the engine. It plays vital role in supporting the states of stability and performance of the vehicle. There are different types of transmissions utilised in the Ford Focus models, and therefore, there may be one or several Motor And Transmission Mounts depending on the design of a specific car. Years ago several types of Motor And Transmission Mounts have been used in Ford Focus cars and every type serves the purpose of maintaining the position of the transmission unit and reducing any forms of vibrations. These typologies may have features totally divergent from one another and may concern the design of the throw and the number of mounts that it can have, these aspects are, in fact, capable of always influencing the final result, and therefore the ride comfort. Lastly, the Motor And Transmission Mount is a critical component of the Ford Focus since it is responsible for the car's performance.

We provide a wide range of Ford Focus Motor And Transmission Mount at the best prices possible. If you need Ford Focus Motor And Transmission Mount, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Focus Motor And Transmission Mount Parts Questions & Experts Answers

Engine Mount Bushing-Right
5S4Z-6038-BB
Q: How to inspect and replace engine/transmission mounts in 2.3L and 2005 and later 2.0L engine on Ford Focus?
A: The engine/transmission mounts should not commonly need inspection or replacement until they are broken or worn but in the event of a broken mount or mount that is worn significantly the mount must be replaced at once with a view of preventing a damage or wear out of the drive line assembly. It is often possible to lift an individual mount and replace it repeatedly and independently Even if several of the mounts are displaced confirming that they should be reunited they will require to be reassembled and their fasteners tightened at the positions which are indicated during their removal. During reassembly the total weight of the engine/transmission unit should not be put on the mounts until all the units come into correct alignment over the marks made at the time of removal of the engine/transmission unit, and the mounting bolts must be tightened up to the prescribed torque. In this case, the engine/transmission unit should be lifted slightly off the mounts to reduce the load upon it, and the car in turn should be firmly placed on axle stands. A jack with a block of wood should be placed directly under the oil pan to lift the engine/transmission just enough in order to offload some weight from the mountings. As for the modes of the vehicle operation, the mounts should be inspected for the cracks, the hardened rubber, the separation from the metal parts of the vehicle or the relative movement of the mount brackets relative to the engine/transmission or the body. If there is movement, the motor should be lowered at that point and the fasteners securing it examined and probably tightened. For replacement, the engine should be supported beneath the oil pan with some form of jackstand. The coolant expansion bottle is anchored to the right-hand mount and the mount operational position is marked on the automobile. The locking nuts of the engine casing should be loosened and the retaining bolts to the inner fender panel of the vehicle should be removed to pull-out the mounting with the engine/transmission supported. In assembly all the nuts and bolts must be tightened to the required torque first is the locking nuts to the engine casing then the mounting bracket to inner fender retaining bolts. In the case of the left-hand mount, few modifications are needed; the air intake hose has to be disconnected and the air cleaner assembly has to be taken off. After the transmission is supported, center retaining nut should be turned counter clockwise to be loosened for the removal of the mount and the outer retaining nut for the dismount of the mount in the mounting bracket. The mounting bracket can be removed by the removal of retaining bolts which are tightened on the bracket. At the time of installation, new self-locking nuts must be used, and all the bolts screwed to the required torque. For the rear mount it has to be removed by loosening the center bolt which is on the subframe and on the transmission and when putting it back it has to be tightened to the required torque.

Related Ford Focus Parts

Browse by Year