How to remove and reinstall the oil pan in 3.0L V6 engine on 2000-2011 Ford Ranger?

To execute it for 2WD models, first remove the negative cable of the battery and take out the oil dipstick. Remove the screws to the fan shroud and place it over the fan and the final step is the removal of the engine, which is mounted on the frame using special mounts. Lift the car and effect proper jack-staning to do the work on the car area very easily. If so fitted remove the retainer clip and separate the connector from low oil level sensor. Discard the oil and put in a fresh oil filter. The mechanical starter motor must be eradicated, as well as front transmission shroud which has the appearance of a cover. Take off the nuts on the engine mounts and lift the engine by 2 inches using the three-bar engine support fixture, and pull off the transmission, and the engine flywheel or drive plate. Take out the passenger side axle beams, it is advised to take of the brake caliper then fasten it somewhere out of the way. Remove the bolts that fix the oil pan into position and then, with the help of a hoist, lift the engine to about two inches so that enough space will be created to allow the oil pan to be freed and taken out-using a little force, if need be. Before fitting, degrease the sealing surfaces of the block and pan, then fit a new gasket to the oil pan in contact adhesive way. Wipe the majority of the 4 to 5 mm thick RTV sealer off the junction of the rear main bearing cap and engine block and the timing chain cover-to-block surface, and put it around the edges of the bearing cap and to the mating area of the cover to the block, making sure that the sealant does not dry up before fitting the pan. Place the pan on the engine, fasten the oil pan bolts, and apply only the recommended amounts of force in order to tighten them. Any parts removed should be reinstalled and the engine oil topped up before engaging the engine to look for any signs of leakage. On the 4WD models, the engine has to be dismantled to get at the oil pan. Next, supporting the engine on a suitable engine stand, have the oil pan bolted, and if required, eased off slightly. Scrub the gasket surfaces nicely and insert a new one that you'll be using contact adhesive; apply a 4 to 5 mm thick of RTV sealer on the relevant joints but make sure the sealant has not cured before you fit the pan. Place the pan in the position of the engine, screw the bolts of the oil pan, and fasten it accordingly. Last but not the least, place back the engine, other components that were unclipped, add the engine oil, and start the engine for leakage test.

Genuine Ford Ranger Oil Pan

Oil Drain Pan

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

19 Oil Pans found

View related parts
Ford Ranger Pan Assembly - Engine Oil
Part Number: 5R3Z-6675-AA
$39.79 MSRP: $57.67
You Save: $17.88 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pan Assy - Engine Oil; Lower Oil Pan, Oil Pan
- Position: Lower
- Replaces: 1L2Z-6675-FA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2011 Ford Ranger | 6 Cyl 4.0L, 6 Cyl 4.0L SOHC EFI | 4AT 4R44E, 5-Speed Automatic Transmission - 5R44E/5R55E, 5-Speed Manual Transmission - R1HD, 5-Speed Manual Transmission M5R1, 5AT 5R44E, 5AT 5R55E, 5MT, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Ranger Frame Assembly
Part Number: 1L5Z-6675-AA
$121.98 MSRP: $178.33
You Save: $56.35 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Frame Assy; Oil Pan, Upper Oil Pan
- Position: Upper
- Replaces: F77Z-6675-BD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2011 Ford Ranger | 6 Cyl 4.0L, 6 Cyl 4.0L SOHC EFI | 4AT 4R44E, 5AT 5R44E, 5AT 5R55E, 5MT, 5-Speed Automatic Transmission - 5R44E/5R55E, 5-Speed Manual Transmission - R1HD, 5-Speed Manual Transmission M5R1, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Ranger Pan Assembly - Engine Oil
Part Number: 1L5Z-6675-BA
$115.14 MSRP: $168.33
You Save: $53.19 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Manufacturer Note: Replacment pan does not require baffle per engineering.
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2011 Ford Ranger | 4 Cyl 2.3L, 4 Cyl 2.3L NA Petrol | 4AT 4R44E, 5AT 5R44E, 5AT 5R55E, 5MT, 5-Speed Automatic Transmission - 5R44E/5R55E, 5-Speed Manual Transmission - R1HD, 5-Speed Manual Transmission M5R1, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Ranger Pan Assembly Engine Oil
Part Number: E7TZ6675E
$118.43 MSRP: $164.52
You Save: $46.09 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1984-1987 Ford Ranger | 4 Cyl 2.0L, 4 Cyl 2.2L, 4 Cyl 2.3L, 6 Cyl 2.8L, 6 Cyl 2.9L | 3AT C3, 3AT C5, 4AT A4LD, 4MT, 5MT
View related parts
Ford Ranger Pan Assembly Engine Oil
Part Number: FO9Z6675A
$70.22 MSRP: $95.95
You Save: $25.73 (27%)
ADD TO CART
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1991-1992 Ford Ranger | 6 Cyl 3.0L | 4AT A4LD, 5MT
View related parts
Ford Ranger Pan Assembly - Engine Oil
Part Number: YL5Z-6675-AA
$115.57 MSRP: $186.67
You Save: $71.10 (39%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Manufacturer Note: w/o low oil sensor
- Replaces: F87Z-6675-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2001 Ford Ranger | 6 Cyl 3.0L | 4AT 4R44E, 5AT 5R44E, 5AT 5R55E, 5MT
View related parts
Ford Ranger PAN ASY - ENGINE OIL
Part Number: KB3Z-6675-A
$125.40 MSRP: $183.33
You Save: $57.93 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Oil Pan
- Replaced by: KB3Z-6675-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019 Ford Ranger | 4 Cyl 2.3L TIVCT DI TC | 10-Speed Automatic Transmission (10R80), 2 Whl L/H Rear Drive-High Ride, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive
View related parts
Ford Ranger Pan Assembly - Engine Oil
Part Number: 1L2Z-6675-FA
$39.79 MSRP: $57.67
You Save: $17.88 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pan Assy - Engine Oil
- Position: Lower
- Replaced by: 5R3Z-6675-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2004 Ford Ranger | 6 Cyl 4.0L, 6 Cyl 4.0L SOHC EFI | 4AT 4R44E, 5AT 5R44E, 5AT 5R55E, 5MT, 5-Speed Automatic Transmission - 5R44E/5R55E, 5-Speed Manual Transmission - R1HD, 5-Speed Manual Transmission M5R1, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Ranger Pan Assembly Engine Oil
Part Number: F4TZ6675B
$302.74 MSRP: $420.55
You Save: $117.81 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1994-2000 Ford Ranger | 6 Cyl 4.0L | 4AT 4R44E, 4AT 4R55E, 4AT A4LD, 5AT 5R55E, 5MT
View related parts
Ford Ranger Pan Assembly - Engine Oil
Part Number: F87Z-6675-AA
$127.68 MSRP: $186.67
You Save: $58.99 (32%)
ADD TO CART
Product Specifications
- Other Name: Pan Assy - Engine Oil
- Manufacturer Note: w/o low oil sensor
- Replaced by: YL5Z-6675-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-1999 Ford Ranger | 6 Cyl 3.0L | 4AT 4R44E, 5AT 5R55E, 5MT
View related parts
Ford Ranger Pan Assembly - Engine Oil
Part Number: F59Z-6675-A
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Manufacturer Note: W/ low oil sensor
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1994 Ford Ranger | 6 Cyl 3.0L | 4AT A4LD, 5MT
View related parts
Ford Ranger Pan Assembly - Engine Oil
Part Number: 2L5Z-6675-AA
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Manufacturer Note: w/o low oil sensor
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2008 Ford Ranger | 6 Cyl 3.0L, 6 Cyl 3.0L OHV EFI | 5AT 5R44E, 5AT 5R55E, 5MT, 5-Speed Automatic Transmission - 5R44E/5R55E, 5-Speed Manual Transmission - R1HD, 5-Speed Manual Transmission M5R1, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive, Rear-Wheel Drive (Left Hand Drive)
View related parts
Ford Ranger Pan Assembly Engine Oil
Part Number: E7RY6675B
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1987-1988 Ford Ranger | 4 Cyl 2.0L, 4 Cyl 2.3L, 6 Cyl 2.9L | 4AT A4LD, 5MT
View related parts
Ford Ranger Pan Assembly - Engine Oil
Part Number: F37Z-6675-A
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1994 Ford Ranger | 4 Cyl 2.3L | 4AT A4LD, 5MT
View related parts
Ford Ranger Pan Assembly - Engine Oil
Part Number: F57Z-6675-A
Product Specifications
- Other Name: PAN ASY - ENGINE OIL
- Manufacturer Note: 14mm drain plug
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-1997 Ford Ranger | 4 Cyl 2.3L | 4AT 4R44E, 4AT 4R55E, 4AT A4LD, 5AT 5R55E, 5MT
View related parts
Ford Ranger Pan Assembly - Engine Oil
Part Number: F57Z-6675-FA
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Manufacturer Note: 12mm drain plug
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1997 Ford Ranger | 4 Cyl 2.3L | 4AT 4R44E, 4AT 4R55E, 5AT 5R55E, 5MT
View related parts
Ford Ranger Pan Assembly - Engine Oil
Part Number: F5TZ-6675-B
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Manufacturer Note: W/O low oil level sender, OHV
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1994-2000 Ford Ranger | 6 Cyl 4.0L | 4AT 4R44E, 4AT 4R55E, 4AT A4LD, 5AT 5R55E, 5MT
View related parts
Ford Ranger Pan Assembly - Engine Oil
Part Number: F87Z-6675-EA
Product Specifications
- Other Name: Pan Assy - Engine Oil; Oil Pan
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2001 Ford Ranger | 4 Cyl 2.5L | 4AT 4R44E, 5AT 5R44E, 5AT 5R55E, 5MT
View related parts
Ford Ranger PAN ASY - ENGINE OIL
Part Number: KB3Z-6675-B
Product Specifications
- Other Name: Oil Pan
- Replaces: KB3Z-6675-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019-2023 Ford Ranger | 4 Cyl 2.3 L GAS, 4 Cyl 2.3L TIVCT DI TC | 10-Speed Automatic Transmission (10R80), 2 Whl L/H Rear Drive-High Ride, Four-Wheel Drive (Part Time) (Left Hand Drive), Left Hand Drive

Ford Ranger Oil Pan

The Oil Pan is the component in Ford Ranger vehicles that holds engine oil in the correct amount and circulates through the engine for correct lubrication and cooling. A wet sum system which is most common with many Ford Ranger models, has its oil collected from the Oil Pan through a pickup tube by an oil pump which circulates the Oil through the engine before it drains into the pan. This design ensures that the oil levels for the engine are well checked so as to ensure that the engine is well lubricated. In the past, the Ford Ranger Oil Pans were produced from stamped steel although new types can be found in cast aluminum to improve on their performance. The has been changed however its basic function remains the same as the development of new materials is a result of new engineering and designing.

We provide a wide range of Ford Ranger Oil Pan at the best prices possible. If you need Ford Ranger Oil Pan, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Ranger Oil Pan Parts Questions & Experts Answers

Frame Assembly
1L5Z-6675-AA
Q: How to remove and reinstall the oil pan in 3.0L V6 engine on 2000-2011 Ford Ranger?
A: To execute it for 2WD models, first remove the negative cable of the battery and take out the oil dipstick. Remove the screws to the fan shroud and place it over the fan and the final step is the removal of the engine, which is mounted on the frame using special mounts. Lift the car and effect proper jack-staning to do the work on the car area very easily. If so fitted remove the retainer clip and separate the connector from low oil level sensor. Discard the oil and put in a fresh oil filter. The mechanical starter motor must be eradicated, as well as front transmission shroud which has the appearance of a cover. Take off the nuts on the engine mounts and lift the engine by 2 inches using the three-bar engine support fixture, and pull off the transmission, and the engine flywheel or drive plate. Take out the passenger side axle beams, it is advised to take of the brake caliper then fasten it somewhere out of the way. Remove the bolts that fix the oil pan into position and then, with the help of a hoist, lift the engine to about two inches so that enough space will be created to allow the oil pan to be freed and taken out-using a little force, if need be. Before fitting, degrease the sealing surfaces of the block and pan, then fit a new gasket to the oil pan in contact adhesive way. Wipe the majority of the 4 to 5 mm thick RTV sealer off the junction of the rear main bearing cap and engine block and the timing chain cover-to-block surface, and put it around the edges of the bearing cap and to the mating area of the cover to the block, making sure that the sealant does not dry up before fitting the pan. Place the pan on the engine, fasten the oil pan bolts, and apply only the recommended amounts of force in order to tighten them. Any parts removed should be reinstalled and the engine oil topped up before engaging the engine to look for any signs of leakage. On the 4WD models, the engine has to be dismantled to get at the oil pan. Next, supporting the engine on a suitable engine stand, have the oil pan bolted, and if required, eased off slightly. Scrub the gasket surfaces nicely and insert a new one that you'll be using contact adhesive; apply a 4 to 5 mm thick of RTV sealer on the relevant joints but make sure the sealant has not cured before you fit the pan. Place the pan in the position of the engine, screw the bolts of the oil pan, and fasten it accordingly. Last but not the least, place back the engine, other components that were unclipped, add the engine oil, and start the engine for leakage test.