How to replace the Door Handle,Door Latch and Door Lock Cylinder on Ford Taurus?

To replace the outside door handle lever the following are the procedures, Removing the trim cap for the outside handle retaining screw and turning the screw counterclockwise until it loosens but does not come out. Secondly, remove the cover of the outside handle and sliding it to the rear, pulling the handle off the handle reinforcement apparatus fit in the door. Slider-check and, if necessary, replace the outer door handle seals as these may be cracked or in very poor condition. For the inside door handle, you have to pull off the trim panel, then you pop out the handle from the door panel, line up the actuator cable along the slot in the handle lever, then you pull the end plug of the cable out before you pry out the actuator bushing. Installation process is the exact opposite to this process. To gain access to the door latch and outside door handle reinforcement the outside door handle lever, door trim-panel, upper and lower actuating rod as well as the keyless entry pad harness if installed must be removed. Disengage the reinforcement mounting fastener, and rotate the assembly inward to be extracted from the interior of the door, then disengage the latch mounting fasteners and extract the latch, as well as the outside door handle reinforcement as a single piece while disconnecting the electrical connection. Door lock cylinder refer to the fact that it cannot be replaced by a new cylinder, the old cylinder has to be chucked and a new unit has to be made from a lock repair package to be obtained from the dealer. To dismantle the lock cylinder further, one has to pull a ring by which it will be possible to extract it from the handle outside door; in assembling, one has to remember that the D-shaped opening in the new lock cylinder, which has to be put in place of the old one, must fit in the D-shaped opening in the lock cylinder lever. Finally, to take out the keyless entry pad the upper trim cap has to be removed then, using a screwdriver the clip that holds the key pad on the reinforcement handle can be released and thus the key pad pulled out and the electrical connector disconnected and the real reverse order is the process of installation.

Genuine Ford Taurus Door Lock Cylinder

Door Lock Cylinder Tumbler

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Door Lock Cylinders found

View related parts
Ford Taurus Cylinder Assembly - Actuating
Part Number: 8S4Z-5421990-A
$43.36 MSRP: $78.98
You Save: $35.62 (46%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder & Key, Lock Cylinder, Lock Cylinder Assy
- Position: Passenger Side
- Replaces: 1L8Z-5421990-AA, 6S4Z-5421990-A, 4M5Z-5421990-AA, 2L8Z-7806082-AA, XS4Z-5421990-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2019 Ford Taurus | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.5L DOHC VCT SMPI, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Cylinder Assembly - Lock
Part Number: 6R3Z-6343262-B
$100.52 MSRP: $152.30
You Save: $51.78 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock Cylinder, Lock Cylinder Assy
- Replaces: 5W4Z-5443262-BB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Cylinder Assembly - Lock
Part Number: 8E5Z-5421991-B
$63.98 MSRP: $93.53
You Save: $29.55 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assy - Lock
- Position: Driver Side
- Replaces: 5L8Z-7821991-AA, 6E5Z-5421991-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2019 Ford Taurus | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.5L DOHC VCT SMPI, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Cylinder Assembly - Lock
Part Number: 6R3Z-6343262-A
$104.17 MSRP: $152.30
You Save: $48.13 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assy - Lock; Lock Cylinder, Lock Cylinder Assy
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Cylinder Assembly - Lock
Part Number: 5F1Z-5443262-CA
$93.79 MSRP: $130.29
You Save: $36.50 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assy - Lock; Lock Cylinder
- Manufacturer Note: Luggage Compartment - less anti-theft/ajar switch, less anti-theft
- Replaces: 1F1Z-5443262-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2009 Ford Taurus | 6 Cyl 3.0L, 6 Cyl 3.5L DOHC VCT SMPI | 4AT 4F50N, 4AT AX4S, 6-Speed Automatic Transaxle - AWF21, 6-Speed Automatic Transmission 6F50, CVT Select Shift Transmission, Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Cylinder Assembly - Lock
Part Number: 5F1Z-5443262-DA
$80.95 MSRP: $110.61
You Save: $29.66 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assy - Lock
- Manufacturer Note: Luggage Compartment - includes anti-theft/ajar switch, with anti-theft,
- Replaces: 3F1Z-5443262-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2007 Ford Taurus | 6 Cyl 3.0L | 4AT 4F50N
View related parts
Ford Taurus Cylinder Assembly - Lock
Part Number: 3F1Z-5443262-BA
$80.95 MSRP: $110.61
You Save: $29.66 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assy - Lock
- Manufacturer Note: Luggage compartment - includes anti-theft/ajar switch, w/anti-theft
- Replaced by: 5F1Z-5443262-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004 Ford Taurus | 6 Cyl 3.0L | 4AT 4F50N
View related parts
Ford Taurus Cylinder Assembly - Lock
Part Number: F8DZ-5406082-AA
$38.70 MSRP: $56.58
You Save: $17.88 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assy - Lock
- Replaced by: 9G1Z-5406082-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-2007 Ford Taurus | 6 Cyl 3.0L, 8 Cyl 3.4L | 4AT 4F50N, 4AT AX4N, 4AT AX4S
View related parts
Ford Taurus Cylinder Assembly - Lock
Part Number: F8DZ-7406082-AB
$38.70 MSRP: $56.58
You Save: $17.88 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assy - Lock
- Manufacturer Note: Storage Compartment
- Replaced by: 9G1Z-5406082-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Ford Taurus | 6 Cyl 3.0L | 4AT 4F50N
View related parts
Ford Taurus Lock Cylinder Less Keys
Part Number: DB5Z-5421990-A
$45.24 MSRP: $65.57
You Save: $20.33 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock Cylinder, Lock Cylinder Assy
- Manufacturer Note: Lock Service Pack - Door
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | 4 Cyl 2.0L EcoBoost (240PS) , 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.5L DOHC T/C, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Cylinder Assembly - Lock
Part Number: 1F1Z-5443262-CA
Product Specifications
- Other Name: Cylinder Assy - Lock
- Manufacturer Note: Luggage compartment, w/o anti-theft
- Replaced by: 5F1Z-5443262-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Ford Taurus | 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transaxle - AWF21, 6-Speed Automatic Transmission 6F50, CVT Select Shift Transmission, Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
- 2002-2005 Ford Taurus | 6 Cyl 3.0L | 4AT 4F50N, 4AT AX4S
View related parts
Ford Taurus Cylinder Assembly - Actuating
Part Number: F8DZ-5443262-BB
Product Specifications
- Other Name: Cylinder Assy - Actuating
- Manufacturer Note: Luggage compartment, without anti-theft
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998 Ford Taurus | 6 Cyl 3.0L, 8 Cyl 3.4L | 4AT AX4N, 4AT AX4S
View related parts
Ford Taurus Cylinder Assembly - Lock
Part Number: F8DZ-5443262-DB
Product Specifications
- Other Name: Cylinder Assy - Lock; Lock Cylinder
- Manufacturer Note: Luggage Compartment , without anti,theft
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999 Ford Taurus | 6 Cyl 3.0L, 8 Cyl 3.4L | 4AT AX4N, 4AT AX4S

Ford Taurus Door Lock Cylinder

The Door Lock Cylinder is situated at the front doors of Ford Taurus, it plays a vital function to lock and unlock the car doors with the help of car key. This mechanism plays an important role for holding the closed position of the vehicle and to permit the access to the interior cabin. As is the case for all the car door lock cylinders, the Ford Taurus may develop some problems after constant use, this means that a key may stick or fail to turn inside the door lock cylinder. Although the majority of the contemporary car brands designed their models with no simple door lock cylinders, the Ford Taurus is still incorporated with it, so the owners should heed the situation of this part. When sounds or signs of failure, for example, when locking or unlocking, is perceived, it is right to replace the Door Lock Cylinder so as to ensure the vehicle has an effective security system.

We provide a wide range of Ford Taurus Door Lock Cylinder at the best prices possible. If you need Ford Taurus Door Lock Cylinder, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Taurus Door Lock Cylinder Parts Questions & Experts Answers

Cylinder Assembly - Lock
8E5Z-5421991-B
Q: How to replace the Door Handle,Door Latch and Door Lock Cylinder on Ford Taurus?
A: To replace the outside door handle lever the following are the procedures, Removing the trim cap for the outside handle retaining screw and turning the screw counterclockwise until it loosens but does not come out. Secondly, remove the cover of the outside handle and sliding it to the rear, pulling the handle off the handle reinforcement apparatus fit in the door. Slider-check and, if necessary, replace the outer door handle seals as these may be cracked or in very poor condition. For the inside door handle, you have to pull off the trim panel, then you pop out the handle from the door panel, line up the actuator cable along the slot in the handle lever, then you pull the end plug of the cable out before you pry out the actuator bushing. Installation process is the exact opposite to this process. To gain access to the door latch and outside door handle reinforcement the outside door handle lever, door trim-panel, upper and lower actuating rod as well as the keyless entry pad harness if installed must be removed. Disengage the reinforcement mounting fastener, and rotate the assembly inward to be extracted from the interior of the door, then disengage the latch mounting fasteners and extract the latch, as well as the outside door handle reinforcement as a single piece while disconnecting the electrical connection. Door lock cylinder refer to the fact that it cannot be replaced by a new cylinder, the old cylinder has to be chucked and a new unit has to be made from a lock repair package to be obtained from the dealer. To dismantle the lock cylinder further, one has to pull a ring by which it will be possible to extract it from the handle outside door; in assembling, one has to remember that the D-shaped opening in the new lock cylinder, which has to be put in place of the old one, must fit in the D-shaped opening in the lock cylinder lever. Finally, to take out the keyless entry pad the upper trim cap has to be removed then, using a screwdriver the clip that holds the key pad on the reinforcement handle can be released and thus the key pad pulled out and the electrical connector disconnected and the real reverse order is the process of installation.