Ford F37Z-9D475-B Valve - Exhaust Gas

You can Select Your Vehicle to check if F37Z-9D475-B fits your vehicle.

To begin with, disconnect the battery so as to perform maintenance on the EGR system components. To install a new O-ring during installation, unplug the electrical connector from the EVP sensor, remove the mounting bolts, and then detach the sensor. Disconnecting the battery is required for EGRC or EGRV Solenoid(s). They can be found on firewall, you will need to unplug the electrical connector, label and detach vacuum hoses, and remove the solenoid if it is held by bracket screws. EVR solenoid requires removing the solenoid, unplugging the sensor harness electrical connector and vacuum hose, and detaching the battery cable. Detach the vacuum line and mounting bolts after unplugging the electrical connector from EGR valve position sensor of the EGR valve. The valve should be removed after taking out the threaded fitting for the external exhaust supply tube (if present), unscrewing the mounting bolting, and removing a vacuum line. The gasket should also be replaced. When substituting an EGR valve without a position sensor; one can transfer the old one to fit with a new O-ring. Disconnect the battery before dealing with TAB/AIRB or TAD/AIRD solenoid(s) on the firewall then unplug the electrical connector from the solenoids located there then mark before removal of their vacuum hoses and solenoid/bracket screws. Labeling and disconnecting hoses are done when replacing faulty components in air pump and control valves on MTA systems before reattaching hoses.

The EGR system helps reduce oxides of nitrogen (NOx) by recirculating exhaust gases from exhaust ports through the EGR valve and back into the intake manifold, thereby lowering peak flame temperature during combustion. Models are equipped with the Electronic Exhaust Gas Recirculation (EEGR) system, which depends on the PCM for EGR control. The EGR flow rate is gauged by monitoring the pressure across a fixed orifice when exhaust gases pass through it, termed the Differential Pressure Feedback (DPFE) system. The system consists of the EGR valve, EGR vacuum regulator (EVR), Powertrain Control Module (PCM), differential feedback pressure sensor, EGR pipe, and various vacuum hoses. For EGR valve replacement, use the code stamped on its top when buying a new one. Turn the ignition OFF, remove the air filter housing, disconnect the EGR valve connector and vacuum hose, detach the EGR pipe, and remove the EGR valve retainer bolts. Clean the EGR valve gasket surface if reusing. For EGR pipe replacement, disconnect the vacuum lines from the DPFE sensor and the pipe at the manifold and valve. For the EVR, disconnect the electrical connector, label and detach vacuum hoses, and remove the regulator. For the DPFE sensor, disconnect the electrical connector, label and detach vacuum hoses, and remove the assembly. The 6.4L diesel engine uses two coolers for its EGR system, with the EGR valve located on top of the engine. It fits into a hole in the intake tract, sealed by an O-ring, and is attached with three bolts. Due to its tight fit, a special tool (Ford #303-1267) is required for removal, suggesting dealership involvement for replacements.

The EGR system reintroduces small metered amounts of exhaust gas back into the intake manifold during part throttle and cruise conditions, where it combines with the air/fuel mixture before combustion, lowering combustion temperatures and reducing NOx emissions.

Checks for ported valves, integral back pressure transducer valve, and electronic EGR valves involve vacuum testing, leakage tests, functional tests, and resistance measurements.

To replace the EGR valve, you need to follow these steps:1. Disconnect the negative battery cable.2. Remove the air cleaner outlet tube.3. Disconnect the EGR valve vacuum hose.4. Disconnect the EGR exhaust manifold tube.5. Remove the EGR valve from the intake manifold.6. Clean the gasket surfaces.7. Install the new valve.

The EGR system accomplishes its purpose by recirculating a small portion of inert exhaust gases into the intake manifold. This lowers the combustion temperature and mitigates the formation of NOx compounds.

The EGR system consists of components such as the EGR valve, EGR vacuum regulator, differential feedback pressure sensor, PCM (Powertrain Control Module), EGR pipe, and vacuum and pressure lines.

The ported vacuum valve operates based on ported vacuum and provides an ideal signal for EGR during part-throttle and cruise conditions.

Replacements of other components related to the air inlet control, deceleration throttle control, intake manifold heating, PCV system, and catalytic converter typically involve disconnecting wires and hoses, removing faulty components, and installing new ones as needed.

It was discontinued due to the introduction of Electronic Engine Control (EEC) systems and their associated EEGR system.

Potential replacements include the EGR valve, EGR vacuum regulator, and DPFE sensor. Safety precautions and protective gear are emphasized during EGR valve and passage cleaning to prevent damage.

The EGR system consists of components such as the EGR valve, EGR vacuum regulator, differential feedback pressure sensor, PCM (Powertrain Control Module), EGR pipe, and vacuum and pressure lines.