How to remove Clutch Disc and Pressure Plate on Ford F-250?

To remove the dust, use brake system cleaner to flush it into a drain pan, and after wiping the clutch components clean with a rag, dispose of the contaminated materials in a covered, marked container. Disconnecting the battery on later models with a Powertrain Control Unit (PCM) may cause the PCM to lose its memory, leading to abnormal driving symptoms for the first 10 miles until it relearns its adaptive strategy. Accessing the clutch components typically requires removing the transmission (and transfer case on 4WD models) while leaving the engine in place; however, if the engine is being overhauled, check the clutch for wear and replace any worn components. On early models with mechanical linkages, remove the clutch rod and equalizer bar from the transmission. For models with an external slave cylinder, remove and tie it up out of the way without disconnecting the hydraulic line; for those with a concentric slave cylinder, detach the clutch line at the inlet port. For 4WD models, remove the transfer case, followed by the transmission. On 3 and 4-speed models with a separate clutch housing, disconnect the negative battery cable, remove the starter motor bolts, and the bolts retaining the clutch housing to the engine block, noting the presence of shims. To support the clutch disc during removal, install a clutch alignment tool through the hub, and inspect the flywheel and pressure plate for indexing marks, making your own if necessary. Loosen the pressure plate-to-flywheel bolts in a criss-cross pattern until all spring pressure is relieved, then remove the bolts, pressure plate, and clutch disc. Inspect the clutch driven plate assembly, flywheel for defects, pilot bearing, clutch disc lining, release bearing, and pressure plate for wear or damage, replacing components as necessary. If the pilot bearing was removed, install a new one, and before installation, clean the flywheel and pressure plate surfaces thoroughly. Position the clutch disc and pressure plate against the flywheel using the alignment tool, ensuring proper installation, and tighten the pressure plate-to-flywheel bolts lightly in a criss-cross pattern. Center the clutch disc and tighten the bolts gradually, then remove the alignment tool. If applicable, install the clutch release bearing and lever or concentric slave cylinder, followed by the clutch housing, ensuring shims are reinstalled if present. Finally, install the transmission and transfer case, reconnect the slave cylinder or clutch line as needed, and bleed the clutch hydraulics if required, then reinstall the clutch rod and equalizer bar on early model mechanical linkages and adjust the linkage.

Genuine Ford F-250 Pressure Plate

Clutch Pressure Plate

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Pressure Plates found

View related parts
Ford F-250 Plate - Clutch Pressure
Part Number: C6AZ-7B066-A
$14.71 MSRP: $21.50
You Save: $6.79 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990-1999 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 4.6L, 8 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.4L, 8 Cyl 5.8L, 8 Cyl 7.3L, 8 Cyl 7.5L | 3AT C6, 4AT 4R100, 4AT 4R70W, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-250 Plate - Clutch Pressure
Part Number: E9SZ-7B066-A
$14.25 MSRP: $20.83
You Save: $6.58 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1993 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L, 8 Cyl 7.3L, 8 Cyl 7.5L | 3AT C6, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-250 Plate - Clutch Pressure
Part Number: F3LY-7B066-A
$21.29 MSRP: $30.33
You Save: $9.04 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 3L3Z-7B066-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-1999 Ford F-250 | 8 Cyl 4.6L, 8 Cyl 5.0L, 8 Cyl 5.4L, 8 Cyl 5.8L | 4AT 4R100, 4AT 4R70W, 4AT E4OD, 5MT
View related parts
Ford F-250 Drive Plate - Clutch
Part Number: E9TZ-7B066-A
$13.73 MSRP: $18.75
You Save: $5.02 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998 Ford F-250 | 8 Cyl 4.6L, 8 Cyl 5.4L | 4AT 4R100, 4AT 4R70W
- 1990-1996 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L, 8 Cyl 7.3L, 8 Cyl 7.5L | 3AT C6, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-250 Plate - Clutch Pressure
Part Number: E9TZ-7B066-B
$16.21 MSRP: $22.15
You Save: $5.94 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-1999 Ford F-250 | 8 Cyl 4.6L, 8 Cyl 5.4L | 4AT 4R100, 4AT 4R70W
- 1990-1993 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L, 8 Cyl 7.3L, 8 Cyl 7.5L | 3AT C6, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-250 Plate - Clutch Pressure
Part Number: E9TZ-7B066-C
$14.03 MSRP: $19.17
You Save: $5.14 (27%)
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990-1999 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 4.6L, 8 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.4L, 8 Cyl 5.8L, 8 Cyl 7.3L, 8 Cyl 7.5L | 3AT C6, 4AT 4R100, 4AT 4R70W, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-250 Plate - Clutch Pressure
Part Number: F7TZ-7B066-AA
$13.73 MSRP: $18.75
You Save: $5.02 (27%)
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-1999 Ford F-250 | 8 Cyl 4.6L, 8 Cyl 5.0L, 8 Cyl 5.4L, 8 Cyl 5.8L | 4AT 4R100, 4AT 4R70W, 4AT E4OD, 5MT
View related parts
Ford F-250 Plate - Clutch Press
Part Number: E7TZ-7563-A
$61.24 MSRP: $83.68
You Save: $22.44 (27%)
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1987-1989 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L, 8 Cyl 6.9L, 8 Cyl 7.3L, 8 Cyl 7.5L | 3MT, 4MT, 5MT
View related parts
Ford F-250 Plate - Clutch Pressure
Part Number: C6AZ-7B066-B
$28.73 MSRP: $42.00
You Save: $13.27 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990-1999 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 4.6L, 8 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.4L, 8 Cyl 5.8L, 8 Cyl 7.3L, 8 Cyl 7.5L | 3AT C6, 4AT 4R100, 4AT 4R70W, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-250 Plate - Clutch Pressure
Part Number: FOSZ-7B066-B
$14.93 MSRP: $21.83
You Save: $6.90 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-1999 Ford F-250 | 8 Cyl 4.6L, 8 Cyl 5.0L, 8 Cyl 5.4L, 8 Cyl 5.8L | 4AT 4R100, 4AT 4R70W, 4AT E4OD, 5MT
- 1990-1993 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L, 8 Cyl 7.3L, 8 Cyl 7.5L | 3AT C6, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-250 Plate - Clutch Pressure
Part Number: XL3Z-7B066-AA
$16.15 MSRP: $23.00
You Save: $6.85 (30%)
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999 Ford F-250 | 8 Cyl 4.6L, 8 Cyl 5.4L | 4AT 4R100, 4AT 4R70W
View related parts
Ford F-250 Cover
Part Number: XL3Z-7563-AA
Product Specifications
- Other Name: Pressure Plate
- Replaced by: 6L3Z-7B546-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999 Ford F-250 | 8 Cyl 4.6L | 5MT
View related parts
Ford F-250 Plate - Clutch Pressure
Part Number: F2TZ-7B066-B
$0.00
Product Specifications
- Manufacturer Note: Front plate - 5 33/64" O.D. - 34 teeth
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-1999 Ford F-250 | 8 Cyl 4.6L, 8 Cyl 5.0L, 8 Cyl 5.4L, 8 Cyl 5.8L | 4AT 4R100, 4AT 4R70W, 4AT E4OD, 5MT
- 1992-1993 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L, 8 Cyl 7.3L, 8 Cyl 7.5L | 3AT C6, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-250 Plate Assembly - Clutch
Part Number: E4TZ-7563-C
Product Specifications
- Other Name: Pressure Plate
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1984-1986 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L, 8 Cyl 6.9L, 8 Cyl 7.5L | 3MT, 4MT
View related parts
Ford F-250 Plate - Clutch Pressure
Part Number: F2TZ-7B066-A
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-1998 Ford F-250 | 8 Cyl 4.6L, 8 Cyl 5.0L, 8 Cyl 5.4L, 8 Cyl 5.8L | 4AT 4R100, 4AT 4R70W, 4AT E4OD, 5MT
- 1992-1993 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.8L, 8 Cyl 7.3L, 8 Cyl 7.5L | 3AT C6, 4AT AOD, 4AT E4OD, 4MT, 5MT
View related parts
Ford F-250 Plate - Clutch Pressure
Part Number: F5TZ-7B066-A
Product Specifications
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-1998 Ford F-250 | 6 Cyl 4.9L, 8 Cyl 4.6L, 8 Cyl 4.9L, 8 Cyl 5.0L, 8 Cyl 5.4L, 8 Cyl 5.8L, 8 Cyl 7.3L, 8 Cyl 7.5L | 3AT C6, 4AT 4R100, 4AT 4R70W, 4AT E4OD, 5MT
View related parts
Ford F-250 Plate - Clutch Pressure
Part Number: F7AZ-7B066-AB
Product Specifications
- Manufacturer Note: .239" thick - used with 6 friction discs
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-1999 Ford F-250 | 8 Cyl 4.6L, 8 Cyl 5.0L, 8 Cyl 5.4L, 8 Cyl 5.8L | 4AT 4R100, 4AT 4R70W, 4AT E4OD, 5MT

Ford F-250 Pressure Plate

We provide a wide range of Ford F-250 Pressure Plate at the best prices possible. If you need Ford F-250 Pressure Plate, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford F-250 Pressure Plate Parts Questions & Experts Answers

Plate - Clutch Pressure
C6AZ-7B066-A
Q: How to remove Clutch Disc and Pressure Plate on Ford F-250?
A: To remove the dust, use brake system cleaner to flush it into a drain pan, and after wiping the clutch components clean with a rag, dispose of the contaminated materials in a covered, marked container. Disconnecting the battery on later models with a Powertrain Control Unit (PCM) may cause the PCM to lose its memory, leading to abnormal driving symptoms for the first 10 miles until it relearns its adaptive strategy. Accessing the clutch components typically requires removing the transmission (and transfer case on 4WD models) while leaving the engine in place; however, if the engine is being overhauled, check the clutch for wear and replace any worn components. On early models with mechanical linkages, remove the clutch rod and equalizer bar from the transmission. For models with an external slave cylinder, remove and tie it up out of the way without disconnecting the hydraulic line; for those with a concentric slave cylinder, detach the clutch line at the inlet port. For 4WD models, remove the transfer case, followed by the transmission. On 3 and 4-speed models with a separate clutch housing, disconnect the negative battery cable, remove the starter motor bolts, and the bolts retaining the clutch housing to the engine block, noting the presence of shims. To support the clutch disc during removal, install a clutch alignment tool through the hub, and inspect the flywheel and pressure plate for indexing marks, making your own if necessary. Loosen the pressure plate-to-flywheel bolts in a criss-cross pattern until all spring pressure is relieved, then remove the bolts, pressure plate, and clutch disc. Inspect the clutch driven plate assembly, flywheel for defects, Pilot Bearing, clutch disc lining, Release Bearing, and pressure plate for wear or damage, replacing components as necessary. If the pilot bearing was removed, install a new one, and before installation, clean the flywheel and pressure plate surfaces thoroughly. Position the clutch disc and pressure plate against the flywheel using the alignment tool, ensuring proper installation, and tighten the pressure plate-to-flywheel bolts lightly in a criss-cross pattern. Center the clutch disc and tighten the bolts gradually, then remove the alignment tool. If applicable, install the clutch release bearing and lever or concentric slave cylinder, followed by the clutch housing, ensuring shims are reinstalled if present. Finally, install the transmission and transfer case, reconnect the slave cylinder or clutch line as needed, and bleed the clutch hydraulics if required, then reinstall the clutch rod and equalizer bar on early model mechanical linkages and adjust the linkage.

Related Ford F-250 Parts

Browse by Year

1999 Pressure Plate 1998 Pressure Plate 1997 Pressure Plate 1996 Pressure Plate 1995 Pressure Plate 1994 Pressure Plate 1993 Pressure Plate 1992 Pressure Plate 1991 Pressure Plate 1990 Pressure Plate 1989 Pressure Plate 1988 Pressure Plate 1987 Pressure Plate 1986 Pressure Plate 1985 Pressure Plate 1984 Pressure Plate