How do you remove and install fuel injectors and the fuel rail on Ford Taurus?

To begin, relieve the fuel system pressure and disconnect the cable from the negative battery terminal. For four-cylinder models, remove the intake manifold, disconnect the high-pressure fuel line from the fuel pump and fuel rail, and disconnect the electrical connectors for all wiring associated with the fuel injectors, followed by the four fuel injector electrical connectors. Use a trim removal tool to disengage the retainers securing the wiring harness to the fuel rail, then clean the area around each injector with compressed air. Remove and discard the fuel rail mounting fasteners, then take out the fuel rail and injectors, using new bolts for installation. If the fuel injectors remain in the cylinder heads, use a removal tool to extract them. Remove the old combustion chamber Teflon sealing ring, upper O-ring, and support ring from each injector, taking care not to damage the groove for the seal. Clean the groove and injector shaft thoroughly before installing the new Teflon seal using the recommended special tools or an alternative method with a socket. After installing the new seals, lubricate the new upper O-ring with clean engine oil and install it on the injector, ensuring the O-ring is above the support ring. Clean the injector bores, insert each injector into its bore in the fuel rail, and secure them with retaining clips. Install the injectors and fuel rail assembly on the cylinder head, tightening the mounting fasteners in the correct sequence. For V6 models, remove the appropriate intake manifold, disconnect the fuel supply line and electrical connectors, detach the retainers, and remove the fuel rail and injectors as a single assembly. Release the injector retaining clips and remove each injector, discarding the old O-rings. Coat the new O-rings with clean engine oil and install them on the injectors, then secure the injectors to the fuel rail. Install the intake manifold gaskets if necessary, attach the fuel rail assembly, and tighten the bolts. Finally, reconnect the cable to the negative battery terminal, turn the ignition switch to ON to activate the fuel pump, and check for fuel leaks.

Genuine Ford Taurus Fuel Rail

Engine Fuel Rail

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

22 Fuel Rails found

View related parts
Ford Taurus Fuel Supply Manifold Assembly
Part Number: CJ5Z-9D280-A
$235.04 MSRP: $431.67
You Save: $196.63 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Fuel Supply; Fuel Rail
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | 4 Cyl 2.0L EcoBoost (240PS) | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Fuel Supply Manifold Assembly
Part Number: 7T4Z-9F792-G
$435.05 MSRP: $641.67
You Save: $206.62 (33%)
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Fuel Supply; Fuel Rail
- Replaces: 7T4Z-9F792-F
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2012 Ford Taurus | 6 Cyl 3.5L DOHC VCT SMPI | 6-Speed Automatic Transaxle - AWF21, 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, CVT Select Shift Transmission, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Fuel Supply Manifold Assembly
Part Number: BA5Z-9D280-A
$82.61 MSRP: $125.17
You Save: $42.56 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Fuel Supply; Fuel Rail
- Position: Passenger Side
- Replaces: AA5Z-9D280-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2019 Ford Taurus | 6 Cyl 3.5L DOHC T/C | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Fuel Supply Manifold Assembly
Part Number: AA5Z-9D280-A
$82.61 MSRP: $125.17
You Save: $42.56 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Fuel ; Manifold Assy - Fuel Supply
- Position: Passenger Side
- Replaced by: BA5Z-9D280-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Ford Taurus | 6 Cyl 3.5L DOHC T/C | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Fuel Supply Manifold Assembly
Part Number: BA5Z-9D280-B
$204.06 MSRP: $298.33
You Save: $94.27 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Fuel Supply; Fuel Rail
- Position: Driver Side
- Replaces: AA5Z-9D280-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2019 Ford Taurus | 6 Cyl 3.5L DOHC T/C | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Fuel Supply Manifold Assembly
Part Number: AT4Z-9F792-A
$196.08 MSRP: $286.67
You Save: $90.59 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Fuel Supply
- Replaced by: GT4Z-9F792-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Taurus | 6 Cyl 3.5L Cyclone Petrol TIVCT, 6 Cyl 3.7L DOHC | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Fuel Supply Manifold Assembly
Part Number: AA5Z-9D280-B
$204.06 MSRP: $298.33
You Save: $94.27 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold Assembly - Fuel ; Manifold Assy - Fuel Supply
- Position: Driver Side
- Replaced by: BA5Z-9D280-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Ford Taurus | 6 Cyl 3.5L DOHC T/C | 6-Speed Automatic Transmission 6F Mid-Range, 6-Speed Automatic Transmission 6F50, 6-Speed Automatic Transmission 6F55, Four-Wheel Drive (Full Time) (Left Hand Drive), Four-Wheel Drive (Part Time) (Left Hand Drive), Front-Wheel Drive (Left Hand Drive), Left Hand Drive
View related parts
Ford Taurus Fuel Supply Manifold Assembly
Part Number: 3F1Z-9F792-JA
$0.00
Product Specifications
- Other Name: Manifold Assembly - Fuel ; Manifold Assy - Fuel Supply; Fuel Rail
- Manufacturer Note: 2V-Flex Fuel(Methanol/Ethanol)
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2007 Ford Taurus | 6 Cyl 3.0L | 4AT 4F50N, 4AT AX4S
View related parts
Ford Taurus Fuel Supply Manifold Assembly
Part Number: 1F1Z-9F792-AA
Product Specifications
- Other Name: Manifold Assembly - Fuel ; Manifold Assy - Fuel Supply; Fuel Rail
- Manufacturer Note: Does not have fuel pressure sensor on it, 4V
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001 Ford Taurus | 6 Cyl 3.0L | 4AT 4F50N, 4AT AX4S
View related parts
Ford Taurus Fuel Supply Manifold Assembly
Part Number: 1F1Z-9F792-CA
Product Specifications
- Other Name: Manifold Assembly - Fuel ; Manifold Assy - Fuel Supply; Fuel Rail
- Manufacturer Note: 2v
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001 Ford Taurus | 6 Cyl 3.0L | 4AT 4F50N, 4AT AX4S
View related parts
Ford Taurus Fuel Supply Manifold Assembly
Part Number: 2F1Z-9F792-DA
Product Specifications
- Other Name: Manifold Assembly - Fuel Supply
- Manufacturer Note: 2V-Flex Fuel(Methanol/Ethanol)
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002 Ford Taurus | 6 Cyl 3.0L | 4AT 4F50N, 4AT AX4S
View related parts
Ford Taurus Fuel Supply Manifold Assembly
Part Number: 2F1Z-9F792-GA
Product Specifications
- Other Name: Manifold Assembly - Fuel Supply
- Manufacturer Note: 2V, From 1-22-02. Before 9-16-02.
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2003 Ford Taurus | 6 Cyl 3.0L | 4AT 4F50N, 4AT AX4S
View related parts
Ford Taurus Fuel Supply Manifold Assembly
Part Number: 3F1Z-9F792-EA
Product Specifications
- Other Name: Manifold Assy - Fuel Supply; Fuel Rail
- Manufacturer Note: 4V
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2007 Ford Taurus | 6 Cyl 3.0L | 4AT 4F50N
View related parts
Ford Taurus Fuel Supply Manifold Assembly
Part Number: 3F1Z-9F792-HA
Product Specifications
- Other Name: Manifold Assembly - Fuel ; Manifold Assy - Fuel Supply; Fuel Rail
- Manufacturer Note: 2V, from 9-16-02.
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2007 Ford Taurus | 6 Cyl 3.0L | 4AT 4F50N, 4AT AX4S
View related parts
Ford Taurus Fuel Manifold Assembly
Part Number: E8DZ-9F792-B
Product Specifications
- Other Name: Manifold Assembly - Fuel
- Manufacturer Note: EXCEPT SC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1988-1990 Ford Taurus | 6 Cyl 3.0L, 6 Cyl 3.8L | 3AT ATX, 4AT AX4S, 4AT AXOD, 5MT
View related parts
Ford Taurus Manifold Assembly Fuel Supply
Part Number: E9DZ9F792A
Product Specifications
- Other Name: Manifold Assy - Fuel Supply
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1987-1991 Ford Taurus | 6 Cyl 3.0L, 6 Cyl 3.8L | 3AT ATX, 4AT AX4S, 4AT AXOD, 4AT AXOD-E, 5MT
View related parts
Ford Taurus Fuel Supply Manifold Assembly
Part Number: F23Z9F792A
Product Specifications
- Other Name: Manifold Assy - Fuel Supply; Fuel Rail
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1993 Ford Taurus | 6 Cyl 3.0L | 4AT AX4S, 4AT AXOD-E, 5MT
View related parts
Ford Taurus Fuel Manifold Assembly
Part Number: F4DZ-9F792-A
Product Specifications
- Other Name: Manifold Assembly - Fuel
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1994-1995 Ford Taurus | 6 Cyl 3.8L | 4AT AX4N, 4AT AX4S, 4AT AXOD-E, 5MT
View related parts
Ford Taurus Manifold Assembly Fuel Supply
Part Number: F6DZ9F792HD
Product Specifications
- Other Name: Manifold Assy - Fuel Supply
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1996-1997 Ford Taurus | 6 Cyl 3.0L | 4AT AX4N, 4AT AX4S
View related parts
Ford Taurus Fuel Supply Manifold Assembly
Part Number: YF1Z-9F792-DA
Product Specifications
- Other Name: Manifold Assembly - Fuel Supply
- Manufacturer Note: 2v
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000 Ford Taurus | 6 Cyl 3.0L | 4AT AX4N, 4AT AX4S

| Page 1 of 2 |Next >

1-20 of 22 Results

Ford Taurus Fuel Rail

We provide a wide range of Ford Taurus Fuel Rail at the best prices possible. If you need Ford Taurus Fuel Rail, you can shop with confidence on our website. All our OEM parts come with a manufacturer's warranty and are delivered to your door step with a fast delivery service.

Ford Taurus Fuel Rail Parts Questions & Experts Answers

Fuel Supply Manifold Assembly
CJ5Z-9D280-A
Q: How do you remove and install fuel injectors and the fuel rail on Ford Taurus?
A: To begin, relieve the fuel system pressure and disconnect the cable from the negative battery terminal. For four-cylinder models, remove the intake manifold, disconnect the high-pressure fuel line from the Fuel Pump and fuel rail, and disconnect the electrical connectors for all wiring associated with the fuel injectors, followed by the four fuel injector electrical connectors. Use a trim removal tool to disengage the retainers securing the wiring harness to the fuel rail, then clean the area around each injector with compressed air. Remove and discard the fuel rail mounting fasteners, then take out the fuel rail and injectors, using new bolts for installation. If the fuel injectors remain in the cylinder heads, use a removal tool to extract them. Remove the old combustion chamber Teflon sealing ring, upper O-ring, and support ring from each injector, taking care not to damage the groove for the seal. Clean the groove and injector shaft thoroughly before installing the new Teflon seal using the recommended special tools or an alternative method with a socket. After installing the new seals, lubricate the new upper O-ring with clean engine oil and install it on the injector, ensuring the O-ring is above the support ring. Clean the injector bores, insert each injector into its bore in the fuel rail, and secure them with retaining clips. Install the injectors and fuel rail assembly on the cylinder head, tightening the mounting fasteners in the correct sequence. For V6 models, remove the appropriate intake manifold, disconnect the fuel supply line and electrical connectors, detach the retainers, and remove the fuel rail and injectors as a single assembly. Release the injector retaining clips and remove each injector, discarding the old O-rings. Coat the new O-rings with clean engine oil and install them on the injectors, then secure the injectors to the fuel rail. Install the intake manifold gaskets if necessary, attach the fuel rail assembly, and tighten the bolts. Finally, reconnect the cable to the negative battery terminal, turn the ignition switch to ON to activate the fuel pump, and check for fuel leaks.